platinum cure silicone rubber for printing pad casting
- Minimum Order Quantity
- 200 Kilograms
- Price Range
- 6.00 - 8.00 USD ($)/Kilograms
- 7 USD ($)/Kilograms
- Product Name
- PLATINUM CURE LIQUID SILICONE RUBBER FOR PAD PRINTING CASTING
- Product Type
- platinum cure silicone rubber for pad printing
- silicone rubber
- red translucent
- casting for printing pad
- 1.1 Gram per cubic centimeter(g/cm3)
It is a two-component addition organic silicone (platinum catalyst ) which can be cured at room temperature and also can be heat cured.
It is colorless or skin-colored oily liquid and becomes soft elastic material after vulcanization, can be used for making soft silicone rubber material.
1.FDA & ROHS certificate.
2.No limitation with product thickness .Can do deep curing .
3.High temperature resistance (can reach 0~250 degrees ) ,acid and alkali-resistance and aging resistanceÃÂ
4.Light viscosity and good flowability .easy for pouring operation .
5.Can be cured both at room temperature or be heated
6.Low shrinkage .Not releasing low molecular during cross-linking process .So the volume is constant .The shrinkage rate is less than 0.1%.
7.Favorable tensile and tear strength
8.High temperature resistance ,acid and alkali-resistance and aging resistanceÃÂ
Operation Instruction for platinum cure liquid silicone rubber for insole
Step 1: Prepare the moldsÃÂ
Prepare an perfect mold and clean it totally before operation .
ÃÂ¯ÃÂ¼ÃÂNotes: Make sure your molds and operation tool cleaned up totally to avoid uncure problem .
Step 2: Mix part A and part B evenly
Take 100 G part A and 100 G part B and mix them evenly.ÃÂ
ÃÂ¯ÃÂ¼ÃÂNotes: Addition cure mold making silicone rubber is two parts flowing liquid, Please follow the step strictly:
1. Weigh the two part exactly by electronic weight.ÃÂ
If any part not in exactly weight , it may cause changing of hardness , or even cause uncure problem.
2. Mix part A and part B evenly.ÃÂ
Otherwise the silicone rubber will be partly cured and this will give birth to difficulties in your final operation. WhatÃÂ¢ÃÂÃÂs more, the finished molds will meet a short life. All of these will cause a waste of silicon rubber.
Step 3: Vacuum pumping
Without exception, this step takes less than 10 minutes. Otherwise, it will cause cross linking reaction, and no more further steps will be available.ÃÂ
Step 4: Pouring castingÃÂ
Clean your molds and brush a layer of release agent (detergent or soap water )on your molds .Pouring the vacuumed mixture silicone on your molds.
Warm tips :
As addition cure silicone is a kind of platinum cure system, which will be easy to cause uncure problem, so kindly follow the tips below
ÃÂ¯ÃÂ¼ÃÂDo not mix with liquid condensation silicone rubber or even the tool which used for condensation siliconeÃÂ
ÃÂ¯ÃÂ¼ÃÂDo not mix with organic matter which contains N, S, P organics and ionic compound like Sn, As,Hg, Ph,
ÃÂ¯ÃÂ¼ÃÂDo not add any pigment or powder into the addition cure silicone rubber without any testing to prevent uncure problem
1.10KG 20kg 25kg or 200kg /drum.
1.It is a kind of non-dangerous goods. This product should be sealed and placed in a cool and dry place which should keep from sunlight and rain .
2.Specially note that the silicone should not touch or mix with compounds including nitrogen, phosphorus, sulfur, tin, lead or metal organic acid.
3.Addition cure Silicone RTV-2 is an environmentally-friendly liquid silicone product, is not easy to burn which can be stored and transported as non-hazardous goods.
4.The shelf life is 12 months from the date of production.
It can be reused after reinspection when it exceeds the storage period.